SR 3D Builder version 0.8.11.5

Quando a informática e o LEGO se unem!
Responder
xSergio74
Full Member
Full Member
Mensagens: 102
Registado: 27 nov 2007, 15:23

SR 3D Builder version 0.8.11.5

Mensagem por xSergio74 » 02 set 2013, 22:13

Hi everybody !!
As promised, even if a week later, here is another program update.
--------------------------------------------------------------------
Before continue: if someone downloaded the program on September 2, 2013 before this announce, probably got a wrong version. If this is the case, download again from now.
--------------------------------------------------------------------

Most important new is support for Mindstorm EV3 parts and a bounce of bug fixes.

As often, here is a presentation video:

Follow a list of changes:

Fixed
- Flexible parts with fixed length can freeze the application
- Hinge Solver now works with 32494.dat parts: just place on their final position and select both of them with the Hinge Solver tool
- Hinge Solver now works with Universal Joint 3L in all cases
- Mirror building now works again
- Using Half pin with stud part can occasionally lead to an error
- Some gears interferences in particular compact mechanisms

Added
- Support for Mindstorm EV3 parts (Thanks to Philo for this!!)
- Latest Official and Unofficial lDraw parts update

Avatar do Utilizador
JMCampos
Sócio
Sócio
Mensagens: 2887
Registado: 08 jul 2007, 21:26
Localização: Amadora
Contacto:

Re: SR 3D Builder version 0.8.11.5

Mensagem por JMCampos » 11 set 2013, 17:01

Hi Sergio,

After installing, when I try to run the program I get the following error message:

Imagem

... and the program will not terminate unless I 'kill' it via Task Manager.

Is there a simple way for me to correct this issue? Thanks a lot!  :fixe:
ImagemJoão
MOCpages

Avatar do Utilizador
Thebicyclestory
Hero Member
Hero Member
Mensagens: 3039
Registado: 03 dez 2012, 18:49
Localização: Oeiras, Lisboa
Contacto:

Re: SR 3D Builder version 0.8.11.5

Mensagem por Thebicyclestory » 11 set 2013, 18:11

I get that same error message too. ???
Filipe Rocha - Sócio nº147 da :plug:

DARK AGE or maybe just busy?

xSergio74
Full Member
Full Member
Mensagens: 102
Registado: 27 nov 2007, 15:23

Re: SR 3D Builder version 0.8.11.5

Mensagem por xSergio74 » 16 set 2013, 07:42

[quote="Thebicyclestory"]
I get that same error message too. ???
[/quote][quote="JMCampos"]
Hi Sergio,

After installing, when I try to run the program I get the following error message:

Imagem

... and the program will not terminate unless I 'kill' it via Task Manager.

Is there a simple way for me to correct this issue? Thanks a lot!  :fixe:
[/quote]

Hi,
if this is the first time you try installing my program and you have a previous lDraw/MLCad installation on your PC then probably that is the problem.
To solve the issue:
- temporary rename any c:\ldraw folder to something else
- reinstall SR3DBuilder. During installation you will be asked for a folder where install part library to: default is c:\ldraw, but you can choose any different folder. If you do not use MLCad then leave default value; if you use MLCad, I recommend you to choose a different folder. Remember your choice.
- let part library extraction complete
- Start SR3DBuilder. If your choice is different from default, you will be asked for the part library folder name
- Let part list inventory to be build (a few seconds or a pair of minute depending on your HW)
- No errors should appear now...

Hope this work.

Sergio

Responder